Two computers cannot ping one another
I''ve got two physical computers which are connected to the same unmanaged switch. Said switch is connected to a server handing out IP
Related Topics:
Ping Access Switch
Cannot ping or ssh outside of VLAN
Now that I''m back at the office, I cannot ping, ssh, or communicate with these switches from my office subnet, which is 172.25.17.x/24. I connected remotely to another switch in the plant
Core to access switch ping working and access to core is not pinging
Look for me Access switch do not aware the IP coming from Core switch to reach back. so make sure Access switch aware routing setup correctly using ip route command.
Ping Command on CISCO Router/Switch
Syntax Router#ping <ip address or DNS name> OR Router#ping Optional Switches data df-bit repeat size source timeout validate Example In this
Performing a Ping Test on a Switch
echo packets to the IP address of the selected switch to check for latency issues. To perform a ping test on switches, complete the following procedure: In the WebUI, select one of the following options: To
Switch is working but will not ping?
Once all the changes had been saved, the switch & pc ip addresses were now able to be pinged. However, back in the office (15mins later) pings have stopped to the switch but not to the pc
ITPro Today, Network Computing, IoT World Today combine
Editor''s note: You may have reached this page because you tried to access a URL on ITPro Today, Network Computing, or IoT World Today that is no longer supported.
Can''t Access Switch GUI, but I can ping it. : r/networking
The management IP was already set on one switch, but the GUI will not pull up. I can ping the management interface from all the other switches, as well as the computer in the same rack.
unable to ping from Access switch 2 to Router
Solved: Hi, I have created a simple network topology with 2 switches and 1 router. switch 1 is directly connected to a router1 via fe port and a switch2 is a trunk link
Can''t ping device on another subnet but can ping SVI''s both ways
My first suggestion would be to test routing from actual hosts/clients connected to access ports in different vlans. I suggest this because testing by pinging from remote switches/routers is not
A device can be pinged from core switch ( router) but not the switch it
I can ping and see the bulk of these devices from my laptop''s ping sweep, but a few devices in the range will act as I described. They can only be pinged from the core fiber switch, which
Access switches can ping endpoint, core cannot.
So an access switch on a different floor, which has to traverse thru the core swtich, can ping the address just fine during times that the core cannot. No logs or issues about Spanning Tree.
Solved: unable to access switch management IP, need to ping it first
I need to logged in on the core switch again and from there ping the IP Address of the access switch to gain remote access again. Hope you can help me out on this one, I have already
Pinging of VLANS (Core and Access Switch)
3. However, when I test from a laptop connected to an access switch (set to access mode for VLAN 10), the laptop can only ping its own gateway, and
How to Use the Ping Command to Test Your Network
And that''s how to use ping at its most basic. Of course, like most commands, there are some advanced switches you can use to make it behave a
Can''t Access Switch GUI, but I can ping it. : r/networking
Hello, we are configuring a remote site of about 10 switches, Netgear M4300''s. The management IP was already set on one switch, but the GUI will not pull up. I can ping the management interface from all
Cannot ping access layer switch, why?
The file attached is our overall configuration. May i know why is it my PC can ping the other PC, distribution layer switch as well as the Router gateway
Setup OK but Cannot Ping Switch
Setup OK but Cannot Ping Switch This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Solved: Can''t ping host from switch
Start a conversation Cisco Community Technology and Support Networking Switching Can''t ping host from switch Bookmark | Subscribe
Solved: Ping between switches
Hello, I have 2 switches that they are connected directly. both have the same vlan 20 for access. I created a new vlan 100 this is a mgmt vlan, on both devices and create a SVI. On the
can not ping the access switch but can putty to it
We have an access 3750 switch connect to the 7K nexus Core - we can putty to it and ping it from other access Cisco switches but we cannot ping it from my PC or from any Server.
Ping Issues on Client and Access Switch
We''re having a strange issue in one of our offices where we''re unable to ping between a machine on one subnet and a server on another local subnet. The symptoms are:
Can ping my switch but unable to access the web interface
Hi, I am reaching out because I am able to ping my HP Switch but unable to access the web interface of the switch. I have an HP Procurve 2524 J4813A. I have done the following:
Testing the path between the switch and another device on an IP
Testing the path between the switch and another device on an IP network The ping test uses ICMP echo requests and ICMP echo replies to determine if another device is alive. It also measures the amount
I can''t ping to the switch before I ping the core!
Hi guys, I have an issue in another city watch is I can''t ping to the switch it said “time out” BUT I can ping the core and after I ping the core I can ping the switch!! It''s weird